Marshall Electronics QVW-1708 Instrucciones de operaciones

Marshall ElectronicsModel No. QVW-170817.3” Quad-Viewer Monitor with 4K Format SupportOperating Instructions

10On Screen MenuAccess and navigate the main menu using the RotoMenu™ knob:Using the RotoMenu knob• Press the RotoMenu™ knob to enter the main menu.•

11To modify a channel, enter a specific submenu (Marker Setup) and a specific function in that submenu (Marker Enable) byhighlighting it with the Roto

12 Marker EnableEnable or disable on screen markers for each individual channel. Marker 16:9, Marker 4:3The Marker 16:9 and Marker 4:3 functions all

131. Allow the monitor to warm up for at least 5-10 minutes.2. Display SMPTE split-field color bars on the monitor using an external source.3. Enable

14 4K ModeUse this setting to enable the 4K Mode, which synchronizes all four inputs to allow the monitor to display a 4K signal.When in 4K mode, all

15Color Configuration SubmenuUse the Color Configuration submenu to adjust the Red, Green and Blue Offset and Gain values of all four input channels.

16System Configuration SubmenuUse the System Configuration submenu to control various system parameters such as GPI, function button settings andUser

17 User-Definable Function ButtonsUse the Function 1 – Function 4 menu items to define each function button on the front panel of the monitor. The fo

18OSD Configuration SubmenuUse the OSD Configuration submenu to select a variety of information to be displayed on the screen. IMD StateUse this sett

19 OSD TallyUse this setting to choose how tally is displayed on the screen. The available OSD Tally options depend on the TallySource selected in th

2Table of ContentsInstallation and Accessories...

20 Anc. MonitorUse the Ancillary Monitor menu option to enable or disable on screen audio, closed caption and timecode presenceindicators. When enabl

21Audio Config SubmenuUse the Audio Configuration submenu to configure Audio channel selection for the headphone jack, audio level and onscreen audio

22 Left Ch. SelectUse this setting to select which of the 16 possible channels you would like to monitor on the Left side of the stereo output. Righ

23 IMD ID #The IMD ID # identifies each screen to the controlling device. When using the TSL protocol, the ID # of each screenshould be manually set

24Use the TSL/MEI 422 setting to control OSD tally via the TSL or Marshall serial protocols. IMD Baud RateUse this setting to choose the baud rate. T

25 IMD Color Use this setting to choose the color of the IMD Fixed String text (see below). Available colors are red, green, and yellow.This setting

26 NetmaskUse this field to set the appropriate Netmask compatible with your network. If you enable DHCP, this will beautomatically set for you based

27Monitor SpecificationsPanel SpecificationsScreen Size 17.3”Screen Resolution 1920 x 1080Brightness 400 cd/m2Contrast Ratio 600:1Burn-In WarningThe Q

28Dimensions

29

3Installation and AccessoriesUnpackingCarefully unpack the QVW-1708 monitor and verify that the following items are included:- QVW-1708 Monitor- V-PS1

30

31

32WarrantyMarshall Electronics warranties to the first consumer that this QVW-1708 LCD monitor will, under normal use, be free from defectsin workmans

4Monitor FrontMonitor Rear

5Front ControlsPOWERControl Power going to the front panel.A – B (Input buttons)Press the A or B to select which module input to displayon the screen.

6Rear InputsLINE OUTThe Line Out, 1/8”, jack on the back of the monitor takestwo channels of embedded SDI audio and provides aLine Level Output. The v

7Compatible Input FormatsSDI / HDSDI Formats567i 50, 625i 59.94720p 23.98, 24, 25, 29.97, 30, 50, 59.94, 601035i 59.94, 601080p 23.98, 23.98sF, 24, 24

8Screen LayoutsThe QVW-1708-Q can display 4 different input sources simultaneously. Each source is scaled and positioned to fit thedesired layout. The

9Quad Layout 3Layout 4